The Deluxe Water Birth Pool

     The versatile oval shape of the Deluxe Pool offers the labouring woman the possibility of lying along the length or using the width to press her feet firmly against the side.

   The head of the pool is tapered and sloped at an angle of 55° to provide comfort and support. The foot of the pool is vertical to enable the mother to squat or kneel.

      Maximum space has been provided for freedom of movement during active childbirth to give the mother the full benefits of the buoyancy of the water.

   The rim of the pool is extra wide (6 inches) at the front for comfort when leaning over. There are 6 grab rails recessed into the rim for use when squatting and to assist entry and exit.

      The pool is designed to be a freestanding unit that does not require boxing in. The absence of a surround creates a space for the midwives legs to be placed under the pool when attending a birth.

      This feature is an important improvement in pool design for midwives. It helps to reduce the possibility of lower back tension caused by leaning over the pool.

   The integral moulded step assists access and egress to the pool and provides support. It can also be used as as stool for the mother to sit or squat on if she needs to be closer to the surface.

   The depth of the pool allows the mother to be deeply immersed and yet accessible to the midwife.

      The Deluxe Pool is fabricated from a high impact weatherable ABS plastic. I have carefully chosen this material rather than GRP fibreglass for the shell.

   Because, it’s harder surface is less brittle. It’s more resistant to bacteria and not affected by the repeated use of sterilising agents.

   The material has a lightly textured, slip resistant internal finish and a smooth, clean external finish. The pool is mounted on a steel frame with adjustable feet and anchor points.

    The pool is supplied fitted with a full length skirting panel. This wrap around panel closely follows the shape and contours of the pool and does not sacrifice the ergonomic design in any way. The panel greatly improves the appearance of the pool as well as making it easier to clean and maintain.

     As the panels will be factory fitted installation will be easier and less costly. The pool needs no building in. It will need to be secured to the floor. There are anchor points on the steel frame for bolting the pool to the floor.

      The Deluxe Pool is fitted with a drain designed to help lower the overall height of the pool. The drain is located at the back of the pool.

   It’s fixed at a slight angle off the horizontal and operated by a rod which controls a gate valve. For installation the pipe work will ideally need to be taken through the floor to the stack.

   If it is not possible to install the pool in this way the pool can be raised for normal drainage connections to the wall behind the pool.

      The Deluxe Pool is being successfully used in over 150 NHS and private maternity units throughout the U.K. and abroad.

Standard Features:

• Factory fitted wrap around skirting panel
• Internal seat - step
• 2 x recessed hand rails
• Fast flow, low profile drain operated with linkage system
• Cowling to conceal drainage system
• Stainless steel base frame with adjustable feet

Optional Equipment

• Underwater Light
• External Step Unit

Specifications

• Length - External 75"/188 cm.
• Width - External 53"/132cm.
• Overall height - 29"/ 72.5 cm. - Depth - 25"/63.5 cm.
• Capacity - 165 gallons/750 litres
• Weight when empty - 200lbs./90 kgs.
• Weight when full -1950lbs./ 886 kgs.
• Colour - soft white

Plan and Elevation

Improvement to the Deluxe Water Birth Pool

   In response to requests from infection control specialists, architects and midwives we have developed a cowling to encase the drainage system on the Deluxe Water Birth Pool.

   The cowling enhances the appearance of the pools, improves hygiene and makes cleaning easier.

   All Deluxe Birth Pools will be supplied with the cowling as standard equipment from July 1, 2008.

   The price of the pool has risen by a small amount to cover the production and development costs of the cowling.

Installation Guidelines

   As the pool is fitted with a full length wrap around skirting it needs no building in. The pool is mounted on a steel frame with adjustable feet and anchor points for bolting the pool to the floor. Once the pool is in place you can drop the skirting panel onto the floor and seal it in with silicone.

Please do not remove the packing until you’re ready
to use the pool as this will help protect the pool during installation

1. Place the pool on the intended site.
2. Place two pieces of timber of equal thickness across the pool (on the lower level of the flange for Active Birth Pool).
3. Lay a spirit level onto the timber both side to side and length ways so that the pool is level from side to side, but has a 20 mm fall towards the tap end.
4. This can be achieved by placing a spacer under the tap end of the spirit level and then adjusting the feet.
5. The fall should be adjusted first ensuring the timber is pushed down onto the flange.
6. Put a mark on the floor around the feet and a cross-under the 2 downward facing bolts near the 2 middle feet for Active Birth (diagonal feet for Deluxe).
7. A hole can be drilled into the floor to either side of bolt [b] for a concrete fixing stud m10. insert and fix to floor.
8. The pool can be repositioned onto the marks and the link plate should be swivelled round to link up to the stud, shim the link plate on the stud with washers so that there is only a slight downward pressure.
9. The pool can now be plumbed in.
10. Slit the top wrapping and remove the enclosed package.
11. Test the pool after installation.
12. Remove the packing from around the pool only. Remove the 3 m8 nuts from under the pool top flange, as you do this the skirt will descend covering the feet and fixings.
13. Seal the skirting panel to the floor with silicone or similar sealant

Typical Installation of the Deluxe Water Birth Pool

   The pool is fitted with a 2” drain designed to help lower it's overall height. The drain is located at the back of the pool. It’s fixed at a slight angle off the horizontal and operated by a handle which controls a ball valve. For installation the pipe work will need to be taken through the floor to the stack.

    If it is not possible to install the pool in this way the pool can be raised for normal drainage connections to the wall behind the pool. If you need the pool raised, we can help by mounting on 10 cm legs at no extra cost if you inform us when placing your order.

    A set of thermostatically controlled 3/4” bath shower mixer taps can be mounted on the wall approximately 15 cm above the rim of the pool. The taps should have as long a spout as possible to help prevent splashing. If you want to mount the taps on the rim - the rim should be strengthened with a plate underneath the section where the taps will be mounted.

   The pool is usually filled to a depth of 22" (55 cm). This exerts a pressure of 95 lbs (43k) per square foot upon the floor of the pool. The New Active Birth Pool weighs approximately 2200 lbs (1,000k) and the Deluxe Pool 1950lbs (886k) when filled to a depth of 22" (55 cm).

   The pool’s frame has four legs with adjustable feet. If necessary the frame/base of the pool can be packed with wood or other suitable material to spread the load across the floor more evenly.

   If the pool room is not ready for use after installation is complete the pool should be resealed with the enclosed packaging to help protect it and keep it clean

Diagram of the steel frame and anchorage assembly

Cleaning Guidelines

   The pools are fabricated from a high impact weatherable ABS plastic. We have carefully chosen this material rather than GRP fibreglass for the shell. Because it’s harder surface is less brittle.

   It’s more resistant to bacteria and not affected by the repeated use of sterilising agents. The material has a lightly textured, slip resistant internal finish and a smooth, clean external finish.

• Before filling the pool rinse it out with cold water and run the taps for two minutes.
• After use the pool must be cleaned with warm water and a non-abrasive detergent.
• Disinfect the pool using either 24 x 0.5 gms or 5 x 2.5 gms Presept Tabs to 3 x 10 lt.. buckets of water.
• Alternatively fill the pool and add presept tabs to the same strength as above.
• Both of these methods will provide a solution of 1000ppm Sodium Dichloroisocy.
• Leave solutions in the pool for 10 minutes ensuring all surfaces are wiped over
• The drainage outlet should be paid particular attention and cleaned with a disposable cloth.
• The pool should then be emptied of the solution and rinsed with cold water and dried.
• The drainage outlet pipe should be kept closed when not in use.
  
• The pool should be cleaned daily with warm water and a non-abrasive detergent.

Over 87% of UK Hospitals that have Installed
a Water Birth Pool have Chosen one of Ours

Here's Why...

• We've met with hundreds of midwives and mothers and worked with architects, engineers and ergonomic specialists to create an unparalleled range of pools.
• Over the past 20 years we have supplied pools to hundreds of hospitals throughout the UK and abroad. (click here for client list)
• Our pools meet all the relevant Health & Safety and Infection Control regulations and protocols.
• Our pools are more expensive, but well worth the price as the superior materials and manufacturing quality ensure decades of service.
• Active Birth Pools pools are backed by a 100% Lifetime Guarantee. *